Mic Not Working in OBS: How to Fix Audio Sources, Monitoring, and Sample Rate Conflicts
Launch Companion Diagnostic Tool
Test your hardware right now in your browser with zero install:
Open Mic TestYour OBS mic is not picking up audio because Windows or macOS has already claimed the device at a conflicting sample rate, or OBS is pointed at the wrong audio source entirely. OBS routes audio through its own internal mixer before it ever touches your stream or recording, so a silent meter in that mixer means the signal is dying somewhere between the physical capsule and OBS's capture thread. The three most common kill points are a mismatched sample rate between the OS audio engine and OBS, an audio input device set to "Default" that resolves to the wrong physical device, and Windows audio enhancements that corrupt or gate the signal before OBS sees it.
Confirm the Microphone Is Actually Working Before Touching OBS
Before you change a single OBS setting, verify the microphone itself is functional. Open Mic Test in your browser and speak into the mic. If the level meter moves, the capsule, cable, and OS driver are all alive. If nothing moves, the problem is upstream of OBS entirely: check that the mic is not muted at the hardware level (physical mute button, mute ring on a USB mic like the Blue Yeti or HyperX QuadCast), confirm the USB port is not bus-powered at a reduced voltage by trying a port directly on the motherboard rear panel, and on XLR mics verify phantom power is engaged on the interface.
On Windows, go to Settings > System > Sound > Input, select your device, and click "Test your microphone." The bar must move. If it does not, right-click the speaker icon in the taskbar, choose Sound settings, scroll to Input, and set the device to 100% input volume. On macOS go to System Settings > Sound > Input and watch the input level indicator while speaking.
Fix the Audio Source Assignment Inside OBS
OBS Studio 29 and later: open Settings > Audio. You will see Global Audio Devices with slots for Mic/Auxiliary Audio through Mic/Auxiliary Audio 4. If your device is listed under one of those slots, it will appear as a permanent source in every scene. If it is not listed there, it must be added as an Audio Input Capture source per scene.
- In the Sources panel, click the plus icon and choose Audio Input Capture.
- Name it, click OK, then open the Device dropdown. Do not leave it on Default. Select the exact device name, for example "Focusrite USB Audio" or "Blue Yeti X."
- Click OK and watch the mixer. The green bar must respond to your voice.
- If the bar is flat, right-click the source in the mixer and choose Properties, then toggle the device off and back on to force a re-enumerate.
If you have the same device assigned in both Global Audio Devices and as a scene source, OBS will double-capture it, which sometimes causes one path to starve the other and go silent. Remove it from one location.
Resolve Sample Rate Conflicts Between Windows and OBS
This is the most common silent-mic scenario. OBS has its own sample rate setting that must match what Windows has negotiated with the audio driver. A mismatch does not always produce an error; OBS frequently just delivers silence.
| Location | Where to Change It | Recommended Value |
|---|---|---|
| OBS global sample rate | Settings > Audio > Sample Rate | 48000 Hz |
| Windows device sample rate | Sound Control Panel > Recording tab > device Properties > Advanced > Default Format | 2 channel, 16 or 24 bit, 48000 Hz |
| macOS aggregate device | Audio MIDI Setup > device > Format | 48000 Hz |
| USB audio interface (e.g. Focusrite Scarlett) | Focusrite Control app > Sample Rate | 48000 Hz |
Set all four locations to 48000 Hz. Restart OBS after changing the OBS setting. After changing the Windows driver setting, OBS must also be restarted because it caches the device format at launch.
On Windows, also disable audio enhancements on the recording device: Sound Control Panel > Recording > your mic > Properties > Enhancements tab > check "Disable all enhancements." On the Advanced tab, uncheck "Allow applications to take exclusive control of this device." Exclusive control allows other apps like Discord or Teams to lock the device and block OBS from capturing it.
Configure Audio Monitoring So You Can Actually Hear What OBS Captures
A flat mixer bar means no signal. A moving bar with no audio in your recording or stream is a monitoring or track routing problem, not a capture problem. These are different failures.
To verify capture is working: in OBS, go to Settings > Audio and set Monitoring Device to your headphones or speakers. Then in the mixer, click the gear icon next to your mic source and choose Advanced Audio Properties. Set Audio Monitoring to Monitor and Output. Put on your headphones. You should hear yourself with a small latency. If you do, the mic is captured correctly and your problem is in the output track assignment.
Check track assignment: in Advanced Audio Properties, confirm the mic source has a checkmark under Track 1 (or whichever track your recording is set to use). Go to Settings > Output > Recording and note which tracks are enabled. They must overlap with the tracks checked for your mic source.
Also confirm your audio is not being silently filtered. If you have a VST plugin inserted on the mic source (Noise Suppression, ReaFIR, or a third-party gate), disable each one temporarily. A gate set with too high an open threshold will mute everything below a loud shout. While you are checking your setup, run Speaker Test to confirm your monitoring output is not the broken link, and use Mic Test again after each change to isolate which fix resolved the issue.
Frequently Asked Questions
Why does my OBS mic work in one scene but not another?
The mic is added as a scene-specific Audio Input Capture source rather than a Global Audio Device. Each scene has its own source list. Either add the mic to every scene individually, or add it once under Settings > Audio as a global device so it persists across all scenes.
OBS shows the mic in the mixer but the bar never moves. What is wrong?
The device is assigned but not delivering signal. The most likely causes in order are: sample rate mismatch between OBS and the Windows driver, another application holding exclusive control of the device, or the physical mic being muted at hardware level. Work through the sample rate table above and disable exclusive mode in the Windows recording device properties.
My mic works in Discord but not in OBS at the same time.
Discord has taken exclusive control of the audio device. In Windows Sound Control Panel, go to Recording > your mic > Properties > Advanced and uncheck "Allow applications to take exclusive control of this device." Both apps can then share the device. Note that some USB mics with onboard DSP, like the Elgato Wave:3, use a proprietary driver that routes through a virtual mixer specifically to avoid this conflict.
Why is my OBS mic picking up audio but it sounds distorted or robotic?
Sample rate mismatch is the primary cause of robotic or pitch-shifted audio. A 44100 Hz device being captured by OBS set to 48000 Hz will sound sped up and distorted. Set both to 48000 Hz as shown in the table above. A secondary cause is bit depth mismatch or a USB mic being overdriven because Windows input volume is set to 100 with the mic gain also maxed out on the hardware.
How do I stop OBS from capturing my system audio on the mic channel?
You have a Desktop Audio source or a second Audio Input Capture source accidentally pointed at a stereo mix or loopback device. In the OBS mixer, mute each source one at a time while making noise to identify which one is capturing system audio, then either remove it or reassign it to the correct device. In Windows, also check that "Stereo Mix" is not enabled as a recording device in Sound Control Panel, as OBS set to Default input may resolve to it.
Does OBS mic not working affect webcam capture too?
Not directly, but if you added your webcam as a Video Capture Device source and also enabled its built-in microphone through that source, an audio conflict on the webcam's audio device can make the video source unstable. Separate them: use the webcam for video only and add the mic as a dedicated Audio Input Capture source. You can verify the webcam itself is functioning independently with Webcam Test.
Launch Companion Diagnostic Tool
Test your hardware right now in your browser with zero install:
Open Mic Test