Keychron Fn Key Not Working: Fix Function Keys on Mac and Windows
Launch Companion Diagnostic Tool
Test your hardware right now in your browser with zero install:
Open Mac Keyboard TesterYour Keychron Fn key is not working because the physical mode switch on the keyboard is set to the wrong operating system, or because Fn Lock is active and you have not toggled it off. Keychron keyboards ship with a three-position or two-position slider on the left side or underside of the board that hard-selects between Windows/Android and Mac/iOS firmware behavior at the hardware level, not in software. When that slider is misaligned even by half a millimeter, the keyboard's onboard microcontroller reads it as an undefined state and the Fn layer either fires the wrong keycodes or produces nothing at all.
Understand the Hardware Mode Switch First
Every Keychron K-series, Q-series, and V-series board has a physical mode switch. On the K8, K2, and K6 it is a three-position slider on the left spine labeled Windows, Mac, and a Bluetooth channel selector. On the Q1, Q5, and V series it is a two-position switch on the underside near the USB-C port. This switch is not a software toggle. It directly changes which keycode table the onboard STM32 or NRF52840 microcontroller references when Fn is held.
- Windows/Android position: Fn + F1 through F12 send multimedia keycodes mapped to Windows HID usage tables. Fn + 1 through 0 send F1 through F10.
- Mac/iOS position: Fn + F1 through F12 send Apple-specific keycodes for Mission Control, Launchpad, brightness, and media. The top row defaults to F1-F12 raw function keys unless Fn Lock is active.
If you are on Windows and the slider is in Mac mode, Fn combinations will either do nothing or trigger incorrect system actions because Windows does not recognize Apple HID consumer page codes. Slide it to Windows mode, unplug and replug the USB-C cable, and retest immediately.
Fn Lock and Default Layer Behavior
Keychron keyboards support Fn Lock, which inverts the default behavior of the top row. With Fn Lock off, the top row sends multimedia keys by default and you hold Fn to get F1-F12. With Fn Lock on, the top row sends raw F1-F12 by default and you hold Fn to get multimedia functions. The combination to toggle Fn Lock varies by model.
| Model | Fn Lock Toggle | Indicator |
|---|---|---|
| K8, K8 Pro | Fn + Caps Lock | Caps Lock LED blinks twice |
| K2, K2 Pro | Fn + Caps Lock | Caps Lock LED blinks twice |
| K6, K6 Pro | Fn + Caps Lock | Caps Lock LED blinks twice |
| Q1, Q1 Pro | Fn + Caps Lock (default layout) | No dedicated indicator, check QMK layer |
| V1, V6 | Fn + Caps Lock | No indicator, QMK-configurable |
If you pressed Fn + Caps Lock accidentally at any point, you flipped the lock state. Press it again to restore. If you are on a Q or V series running QMK firmware, the Fn Lock state is stored in EEPROM. A full EEPROM reset via QMK Toolbox will clear it: connect the board, open QMK Toolbox, check the EEPROM reset option, and click Flash with the keyboard in bootloader mode (hold Escape while plugging in USB-C).
Mac-Specific Fixes: System Preferences and Karabiner
On macOS, even with the slider correctly in Mac mode, System Preferences can override Fn key behavior at the OS level. Go to System Preferences, then Keyboard, then the Keyboard tab. You will see a checkbox labeled "Use F1, F2, etc. keys as standard function keys." If that box is checked, macOS expects a physical Fn key press to access media functions, which is the inverse of Keychron's default Fn Lock off behavior. Uncheck it if you want the top row to default to media keys, or check it if you want raw F-keys by default and use Fn for media. These two settings must agree or every Fn combination will feel backwards.
For keychron function keys not working mac situations that persist after the above, install Karabiner-Elements. Open it, go to Simple Modifications, select your Keychron device from the dropdown, and verify no existing rule is remapping Fn or the F-key range. A stale rule from a previous setup will silently swallow keycodes before any application sees them. Delete any Fn-related rules and retest with the Mac Keyboard Test to confirm each F-key registers the correct keycode.
Windows-Specific Fixes and Driver Conflicts
On Windows, keychron function keys not working windows problems almost always trace back to one of three causes: wrong slider position, HID filter drivers left behind by previous keyboard software, or a BIOS-level Fn Lock on a laptop that intercepts the keycodes before they reach the Keychron.
- Confirm the mode slider is in the Windows/Android position. Unplug, move the slider firmly until it clicks, replug.
- Open Device Manager, expand Human Interface Devices, and look for any entry named after a previous keyboard brand (SteelSeries, Logitech G Hub HID Filter, Razer HID). Right-click and uninstall with the delete driver checkbox checked. These HID filter drivers sit above the USB HID class driver in the stack and can intercept consumer page keycodes that Keychron sends on Fn combinations.
- If you are using a laptop with its own Fn key, enter BIOS setup (usually F2 or Delete at POST), find the Keyboard or System Configuration section, and look for an option called Action Keys Mode or Fn Key Behavior. Set it to Function Keys so the laptop does not consume Fn presses before they reach the Keychron over USB.
Use the Keyboard Test tool to verify each F-key is sending the correct keycode after your changes. Press each F1 through F12 individually without holding Fn, then repeat while holding Fn, and confirm the output matches your expected layer.
QMK and Via Remapping on Pro and Q/V Series
The K8 Pro, K2 Pro, K6 Pro, Q1, Q5, and V-series boards run QMK firmware and support Via or Keychron's own launcher for live remapping. If you or a previous user remapped the Fn key or any key in the Fn layer through Via, those changes persist in EEPROM across reboots and cable swaps. Open Via at the web interface (usevia.app), connect your board, go to the Configure tab, select Layer 1 (the Fn layer), and inspect every key position. Any key showing KC_TRNS is transparent and passes through to Layer 0. Any key showing KC_NO will produce nothing. Restore the Keychron default layout JSON from their GitHub releases page for your specific model to reset all layers at once.
Frequently Asked Questions
Why does my Keychron K8 Fn key not work only in certain applications?
Some applications, particularly remote desktop clients like Microsoft RDP and VMware Horizon, capture F-key combinations at the application layer before the OS sees them. Inside the remote session, the remote machine's Fn behavior applies. Switch focus away from the remote window and test locally to isolate the cause.
My Fn key works but only some F-key combinations respond. What is wrong?
You are likely in the correct mode but have a partial Fn Lock state combined with an OS-level override. On Mac, the System Preferences Keyboard setting and Keychron's Fn Lock must be configured as a matched pair. On Windows, a HID filter driver may be passing some consumer page codes and blocking others depending on which usage IDs it handles.
How do I know which firmware version my Keychron is running?
For QMK-based models, connect the board, open QMK Toolbox, and the detected firmware version appears in the log when the board enumerates. For non-QMK models like the K8 and K2 original versions, Keychron does not expose a firmware version query over USB. Check the Keychron support page for your model's latest firmware file and compare the file date against your purchase date to determine if you need to update.
Can I use the Keychron in Windows mode on a Mac?
Yes, and some users prefer it. In Windows mode on Mac, the top row sends raw F1-F12 by default without needing to hold Fn, which is useful in applications like Logic Pro or Final Cut that rely on bare F-keys. You lose the Apple-specific keycodes for Mission Control and Launchpad, but you can reassign those in System Preferences under Keyboard Shortcuts.
The slider is in the correct position but Fn still does nothing. What next?
The slider's contact pads on the PCB can oxidize, especially on boards that have been stored. With the board unplugged, move the slider back and forth rapidly ten to fifteen times to scrape the contacts clean. If you have isopropyl alcohol at 90 percent or higher and a fine brush, apply a small amount to the slider channel and work it in. Replug and test. If it still fails, the slider switch itself may need replacement, which is a through-hole component on most Keychron PCBs and costs under $5 from any electronics supplier.
How do I test if my function keys are actually sending keycodes after fixing the settings?
Use the Mac Keyboard Test on macOS or the standard Keyboard Test on Windows. Press each F-key individually and confirm the on-screen highlight matches the physical key. Then hold Fn and press each F-key again to verify the Fn layer keycodes are registering correctly. This rules out any remaining software interception before you conclude the hardware is at fault.
Launch Companion Diagnostic Tool
Test your hardware right now in your browser with zero install:
Open Mac Keyboard Tester