How to Make Your Glorious Model O Double Click: The 0ms Debounce Fix

Published on 2026-11-08 ยท 7 min read ยท By MiniTestLab Engineering Team ยท Category: Gaming & Reflexes

Launch Companion Diagnostic Tool

Test your hardware right now in your browser with zero install:

Open CPS Test โ€” Click Speed Test

Set your Glorious Model O debounce time to 0ms in Glorious CORE software and your mouse will register double clicks. The stock debounce value of 10ms is intentionally high enough to filter out the natural contact bounce of the Omron D2FC-F-7N microswitch, which means rapid successive clicks within that window get collapsed into a single input. Dropping that value to 0ms removes the filter entirely, letting the firmware pass every electrical transition the switch produces straight to the host.

Why the Omron D2FC-F-7N Causes This in the First Place

The Glorious Model O ships with Omron D2FC-F-7N microswitches on both primary buttons. These are membrane-over-contact switches with a rated actuation life of 20 million clicks. On each press and release, the phosphor-bronze contact leaf physically bounces two to five times over roughly 1 to 5 milliseconds before settling. That bounce is electrically identical to multiple clicks. The mouse firmware applies a debounce window to ignore any state transitions that happen within a set number of milliseconds of the first detected transition. At 10ms, the firmware is aggressive enough to prevent bounce misregistration but also aggressive enough to eat a legitimate second click from a fast human finger or a butterfly-click technique. At 0ms, every transition goes through raw.

This is not a defect. Glorious ships the mouse with a conservative debounce because most users do not want phantom double clicks from a worn switch. You are deliberately trading that protection for responsiveness.

Exact Steps to Set Debounce to 0ms in Glorious CORE

  1. Download and install Glorious CORE from gloriousgaming.com. The version must be 1.0.18 or later; earlier builds do not expose the debounce slider for the Model O.
  2. Plug the Model O into a USB 2.0 or 3.0 port directly on the motherboard, not through a hub. CORE sometimes fails to detect the mouse through unpowered hubs.
  3. Open CORE. The Model O should appear on the home screen with a render of the mouse. Click it to enter the device configuration panel.
  4. Navigate to Performance in the left sidebar. Do not confuse this with the Keybinds tab.
  5. Locate the Debounce Time slider. The default reads 10ms. Drag it fully left to 0ms.
  6. Click Save to Mouse in the bottom right. CORE will push the value to onboard memory. The mouse stores this in its onboard profile, so it persists without CORE running.
  7. Unplug and replug the mouse to confirm the firmware applied the setting. Re-open CORE and verify the slider still reads 0ms.

If the Performance tab is greyed out, your CORE installation is not recognizing the mouse firmware version. Navigate to Device > Firmware Update and apply the latest firmware first, then return to Performance.

Debounce Value Comparison: What Each Setting Actually Does

Debounce Setting Minimum Gap Between Registered Clicks Practical Effect Best For
0ms None โ€” every transition registers Double clicks register freely; worn switches may misfire Double clicking, butterfly clicking, drag clicking
4ms 4 milliseconds Eliminates most contact bounce; still allows very fast intentional double clicks Competitive gaming with fast click rate
10ms (default) 10 milliseconds Reliable single-click accuracy; blocks most intentional double clicking techniques General use, productivity, new switch life
20ms 20 milliseconds Very conservative; compensates for worn or chattering switches Aging switch with contact chatter problems

Verifying Your Double Click Rate After the Change

Once you have saved the 0ms setting, you need to confirm the mouse is actually registering double clicks before assuming the change worked. Use the Double Click Test on this site. Click as fast as you can and watch whether the tool logs two separate click events per physical press. If you are seeing only single registrations, either the firmware did not save correctly or your click speed is not fast enough to produce two inputs within the tool's detection window.

To measure your raw clicks per second and establish a baseline for your technique, run the CPS Test. A consistent score above 10 CPS with the 0ms debounce set means the firmware change is working. If you are attempting butterfly clicking and want to track that specifically, the Butterfly Click Test will give you a more targeted measurement for that input pattern.

If your CPS numbers look correct but you are still not registering double clicks in a game, the issue is almost certainly the game's own input handling or anti-cheat layer, not the mouse. Minecraft's client, for example, has its own click cooldown tied to attack speed that operates independently of mouse hardware entirely.

When 0ms Debounce Creates Problems Instead of Fixing Them

Running at 0ms debounce on a D2FC-F-7N that has accumulated significant wear will produce unintentional double clicks during normal use. The contact leaf on a high-mileage Omron switch bounces longer and more erratically than a fresh one. If you are seeing phantom double clicks in your operating system file manager or browser, your switch is worn enough that 0ms is exposing real contact bounce rather than just enabling fast intentional inputs. In that case you have two options: replace the microswitches with fresh D2FC-F-7N units (available in 10-packs for under $5 from electronics suppliers) or swap to Kailh GM 8.0 switches, which have a shorter and more consistent bounce characteristic and tolerate 0ms debounce better on older hardware. The Model O PCB uses standard through-hole switch footprints and the swap takes about 20 minutes with a soldering iron.

Also note that 0ms debounce disables the firmware-level protection against switch chatter entirely. If you are using this mouse for anything outside of the specific clicking technique that requires it, consider creating a second onboard profile in CORE with the default 10ms value and switching between profiles as needed.

Frequently Asked Questions

Does setting debounce to 0ms void the Glorious warranty?

No. Debounce is a firmware-level software setting exposed by Glorious in their own official CORE application. Changing it does not physically modify the hardware and does not affect warranty status. Physically opening the mouse shell and modifying the PCB would be a different matter.

Why does my Model O still not double click in Minecraft after setting 0ms?

Minecraft Java Edition applies a server-side and client-side attack cooldown that prevents rapid block placement or attack registration regardless of mouse input speed. This is a game mechanic, not a hardware limitation. The 0ms debounce setting is working correctly if the Double Click Test confirms two registered clicks per action.

What is the difference between the Model O and Model O Wireless for this setting?

The Model O Wireless uses the same CORE software path and the same debounce slider, but the wireless firmware has an additional latency layer from the 2.4GHz receiver. The debounce setting itself behaves identically. Set it to 0ms the same way. The receiver polling rate should be set to 1000Hz in CORE under the Performance tab to minimize any additional input delay.

Can I set debounce to 0ms without installing CORE software?

No. The debounce value is written to onboard memory through CORE's firmware communication protocol. There is no physical DIP switch or hardware method to adjust it. You need CORE installed at least long enough to push the setting, after which you can uninstall CORE and the setting persists in onboard memory.

Will 0ms debounce improve my CPS score?

It removes the firmware ceiling that was blocking rapid inputs, so yes, if your technique was previously being filtered out, your measured CPS will increase. Whether your finger speed actually produces clicks fast enough to benefit depends on your technique. Run the CPS Test before and after the change to see your actual improvement.

My CORE software does not show a debounce slider at all. What is wrong?

You are either running an outdated version of CORE or the mouse firmware is too old for CORE to recognize the device fully. Go to Device > Firmware Update inside CORE and apply the current firmware. If the mouse does not appear in CORE at all, try a different USB port, disable USB selective suspend in Windows power settings under Control Panel > Power Options > Change plan settings > Change advanced power settings > USB settings > USB selective suspend setting > Disabled, then restart CORE.

Launch Companion Diagnostic Tool

Test your hardware right now in your browser with zero install:

Open CPS Test โ€” Click Speed Test